How to Connect a NOAA Weather Radio to a Bellman Flash Receiver: Step-by-Step Setup Guide
Share

This guide covers the complete connection from radio to receiver. It lists every component, walks through each cable step, and explains SAME code programming. It also covers adding a Bed Shaker and troubleshooting steps.
- What components do you need?
- How does the connection work?
- Step-by-step connection guide
- How to find and program your county SAME code
- How to add a Bed Shaker for overnight alerts
- Which NOAA alerts activate the Flash Receiver?
- Troubleshooting: what to check if the system does not activate
- People also ask
Plug the Midland SYCBL Y-cable into the EXT ALERT jack on the Midland WR120. Connect the Bellman Cable Kit (BE9126) from one Y-cable socket to the EXT TRIGGER input on the Flash Receiver. Leave the second Y-cable socket unused. Program your county SAME code into the radio. When your county gets a warning, the radio signals the Flash Receiver to activate.
Full setup overview at: us.bellman.com/pages/weather-emergency-alerting.
Affiliation note: Bellman is not affiliated with Midland. The WR120 and SYCBL Y-cable are sold separately by Midland at midlandusa.com. All Midland trademarks belong to Midland. Bellman receives no compensation for Midland purchases.
What Components Do You Need?
The setup uses five items. Two are Midland products purchased from Midland. Three are Bellman products available at us.bellman.com.
| Component | Model | Where to Buy | Role in the Setup |
|---|---|---|---|
| Midland NOAA Weather Radio | WR120 | midlandusa.com (sold separately) | Receives NOAA weather alerts and sends the trigger signal |
| Midland Y-Cable | SYCBL | midlandusa.com (sold separately) | Connects the radio's EXT ALERT jack to the Bellman Cable Kit |
| Bellman Cable Kit | BE9126 | us.bellman.com | Connects the Y-cable to the Flash Receiver's EXT TRIGGER input |
| Bellman Flash Receiver | BE1442-433-A | us.bellman.com | Converts the trigger signal into flashing light and optional vibration |
| Bellman Bed Shaker (optional) | BE1270 | us.bellman.com | Adds vibration under the pillow or mattress for overnight alerts |
You do not need Wi-Fi, an app account, or a subscription. The connection is wired. It works independently of the internet and cellular networks.
How Does the Connection Work?
Understanding what each component does makes the connection steps easier to follow.
The Midland WR120 monitors NOAA Weather Radio broadcasts 24 hours a day. When an alert is issued for your programmed county, the radio activates. It sounds an alert tone and broadcasts a voice announcement. At the same moment, it fires a trigger signal through the EXT ALERT jack on its back panel.
That signal travels via the Y-cable and Cable Kit to the EXT TRIGGER input on the Flash Receiver. The Flash Receiver fires its 30-candela xenon flash and color-coded LED indicators. If a Bed Shaker is connected, it also vibrates.
The Flash Receiver also receives wireless signals from other Bellman transmitters. The cable connection described here is for NOAA weather alerts only. The cable connection does not affect its wireless function for door, smoke, or phone alerts.
Step-by-Step Connection Guide

Have the Midland WR120, SYCBL Y-cable, Bellman Cable Kit (BE9126), and Flash Receiver ready. If you are adding a Bed Shaker, have that ready too.
Turn the Midland WR120 so the back panel faces you. Find the jack labeled EXT ALERT. It is a 3.5 mm mono jack. This is where the Y-cable plugs in.
Insert the SYCBL Y-cable's single plug into the EXT ALERT jack on the back of the WR120. Push it in firmly until it seats fully. A loose connection will prevent the signal from reaching the Flash Receiver.
The Y-cable has one plug and two sockets. After plugging in, two sockets are available. You will use one of them in the next step.
Take the Bellman Cable Kit (BE9126). Plug one end into one of the two sockets on the Y-cable.
Find the EXT TRIGGER input on the back of the Flash Receiver. Plug the other end of the Bellman Cable Kit into this input. Push it in until it is fully seated.
The EXT TRIGGER input tells the Flash Receiver to activate on receiving a cable signal. This completes the main connection path.
Plug the Flash Receiver into a wall outlet using its power adapter. The receiver's backup batteries are pre-installed. They charge automatically while plugged in. Keep the receiver plugged in during normal use to maintain battery charge.
Turn on the Midland WR120. Tune it to a NOAA Weather Radio transmitter that covers your county. Visit weather.gov/nwr/counties to find the transmitter frequency for your county. Set that frequency on the radio.
Find your six-digit county SAME code at weather.gov/nwr/counties. Enter it into the Midland WR120 following the radio's user manual programming steps. This filters alerts to your county only.
See the SAME code section below for details on finding and entering the code.
Press the TEST button on the WR120. It sends a signal through the EXT ALERT jack. The Flash Receiver should activate immediately with flashing lights. If a Bed Shaker is connected, it should also vibrate.
How to Find and Program Your County SAME Code
SAME stands for Specific Area Message Encoding. It is a digital code the NWS broadcasts alongside every weather alert. A NOAA radio with your SAME code only activates for alerts in your county.
Without a SAME code, the radio activates for every alert in the transmitter's coverage area. That may include alerts for many counties around you. Your SAME code ensures the Flash Receiver only fires for alerts in your area.
What a SAME code looks like
A SAME code is a six-digit number in the format PSSCCC. P is a code for point type (usually 0). SS is the two-digit state code. CCC is the three-digit county code. For example, the SAME code for Harris County, Texas is 048201.
Three ways to find your code
- NWS website: Visit weather.gov/nwr/counties, select your state, and find your county in the table. The SAME code is listed alongside your county name.
- Toll-free hotline: Call 1-888-NWR-SAME (1-888-697-7263). An automated system guides you to your county SAME code and local transmitter frequency.
- Radio manual: Some Midland WR120 user manuals include SAME code resources. Check the documentation that came with your radio.
How to enter the code into the Midland WR120
The exact button sequence for programming the SAME code varies by firmware version. Follow the programming instructions in the Midland WR120 user manual. The manual is available from Midland at midlandusa.com. Bellman cannot provide radio programming support for Midland products.
Most NOAA weather radios accept more than one county SAME code. Program both your home county and workplace county codes if needed. The radio activates for alerts in any of your programmed counties.
How to Add a Bed Shaker for Overnight Alerts

The Bellman Bed Shaker is an optional add-on. It vibrates strongly under the pillow or mattress when the Flash Receiver activates. It is key for overnight use when visual alerts alone may not wake a sleeper.
Bellman Bed Shaker (BE1270)
How to connect the Bed Shaker
- Locate the bed shaker outlet on the Bellman Flash Receiver
- Plug the Bed Shaker's 3.5 mm mono plug into this outlet
- Run the cable from the receiver to your bed
- Place the Bed Shaker under your pillow or between the mattress and mattress pad
- Test by using the radio's TEST function. The Bed Shaker should vibrate at the same time as the Flash Receiver activates.
Overnight setup guide: Silent Weather Alerts at Night for Deaf and Hard-of-Hearing People.
Which NOAA Alerts Activate the Flash Receiver?
The Flash Receiver activates whenever the WR120 receives a valid NOAA alert for your county and fires the trigger signal.
NOAA Weather Radio All Hazards broadcasts a wide range of alert types. All of them flow through the same EXT ALERT jack connection. This means the same Flash Receiver setup covers:
- Tornado warnings and watches (from the NOAA Storm Prediction Center and local NWS offices)
- Hurricane watches and warnings (from the National Hurricane Center and local NWS offices)
- Winter storm warnings and blizzard warnings (from local NWS offices)
- Ice storm warnings (from local NWS offices)
- Flash flood warnings (from local NWS offices)
- Severe thunderstorm warnings (from local NWS offices)
- Red Flag Warnings and Fire Weather Watches (from SPC and local NWS offices)
- Other hazards including AMBER Alerts and chemical spill notices, all broadcast on NOAA Weather Radio All Hazards
Air Quality Index (AQI) alerts are not broadcast on NOAA Weather Radio. They come through separate channels including AirNow.gov and Wireless Emergency Alerts on smartphones. The Flash Receiver setup does not cover AQI alerts.
Troubleshooting: What to Check If the System Does Not Activate
If the Flash Receiver does not activate on the TEST button, work through these checks in order. Each step addresses the most common failure points.
| Symptom | What to Check |
|---|---|
| Flash Receiver does not activate during test |
Check 1: Is the SYCBL Y-cable fully seated in the EXT ALERT jack on the back of the WR120? Pull it out and push it back in firmly. Check 2: Is the Bellman Cable Kit plugged into one of the two Y-cable sockets? Not the radio's other jacks. Check 3: Is the other end of the Cable Kit seated in the EXT TRIGGER input on the Flash Receiver? Not the bed shaker outlet or any other port. Check 4: Is the Flash Receiver plugged in and powered on? Check 5: Is the radio in the correct mode to send a signal through the EXT ALERT jack during test? Consult the Midland WR120 user manual for the correct test procedure. |
| Flash Receiver activates during test but not during real alerts |
Check 1: Is the SAME code programmed correctly? A wrong code means the radio ignores alerts for your county. Check 2: Is the radio tuned to a frequency that covers your county? Visit weather.gov/nwr/counties to confirm the right frequency. Check 3: Is the radio's alert mode enabled? Some modes mute alerts without disabling the EXT ALERT jack. Check the radio's alert settings in its user manual. |
| Bed Shaker does not vibrate during test |
Check 1: Is the Bed Shaker plugged into the bed shaker outlet on the Flash Receiver, not the EXT TRIGGER input? Check 2: Is the plug fully seated? The 3.5 mm mono plug can feel seated but still be slightly loose. |
| Flash Receiver activates randomly with no alert issued |
Check 1: Is the second Y-cable socket left unused? Plugging something into it may cause false signals. Check 2: Check that the cable connections are not near a source of electromagnetic interference such as a motor or power strip. |
| Radio is not receiving any NOAA signal |
Check 1: Is the radio tuned to a valid NOAA Weather Radio frequency? The seven frequencies are 162.400, 162.425, 162.450, 162.475, 162.500, 162.525, and 162.550 MHz. Check 2: Is the radio in an area with adequate signal? NOAA transmitters typically cover about a 40-mile radius on level terrain. Buildings and terrain can reduce range. Check 3: Try moving the radio to a window-side location to improve signal reception. |
For WR120-specific questions, programming issues, or Y-cable faults, contact Midland support at midlandusa.com. Bellman cannot provide support for Midland products.
Ready to build your weather alert system?
See all Bellman products for the weather emergency alert setup.
People Also Ask
How do I connect a NOAA weather radio to a Bellman Flash Receiver?
Plug the Midland SYCBL Y-cable into the EXT ALERT jack on the Midland WR120. Connect the Bellman Cable Kit (BE9126) from one Y-cable socket to the EXT TRIGGER input on the Flash Receiver. Leave the second Y-cable socket unused. When the radio detects a warning for your county, it fires a signal through the cables. The Flash Receiver then activates.
What cable do I need to connect a NOAA weather radio to a Bellman Flash Receiver?
You need two cables. The Midland SYCBL Y-cable (from Midland) plugs into the radio's EXT ALERT jack. The Bellman Cable Kit BE9126 (at us.bellman.com) connects the Y-cable to the Flash Receiver's EXT TRIGGER input.
What is the EXT ALERT jack on the Midland WR120?
The EXT ALERT jack is a 3.5 mm mono jack on the back of the WR120. When the radio detects an alert for your county, it sends a trigger signal through this jack. It is the starting point for the cable connection to the Flash Receiver.
Why do I need a Y-cable for this setup?
The Midland WR120's EXT ALERT jack outputs a single trigger signal. The Midland SYCBL Y-cable splits this into two sockets. Only one of the Y-cable's two sockets is used in this setup. The second socket stays unused. The Y-cable is a Midland accessory purchased separately from Midland.
What is the EXT TRIGGER input on the Bellman Flash Receiver?
The EXT TRIGGER input is a socket on the back of the Flash Receiver. When it receives a signal, it activates the flashing lights and any connected Bed Shaker. The Bellman Cable Kit connects here, completing the link from the NOAA radio to the visual alert output.
How do I find my county SAME code for a NOAA weather radio?
Visit weather.gov/nwr/counties and select your state to find your county's six-digit SAME code. You can also call 1-888-NWR-SAME (1-888-697-7263) for automated code lookup. Enter the code into the WR120 following the radio's programming instructions for your county.
My Flash Receiver is not activating during the radio test. What should I check?
Check five things. Is the Y-cable fully seated in the EXT ALERT jack on the back of the radio? Is the Bellman Cable Kit plugged into one of the two Y-cable sockets? Is the other end of the Cable Kit plugged into the EXT TRIGGER input on the Flash Receiver? Is the Flash Receiver powered on? Is the radio in the correct mode to send a test signal through the EXT ALERT jack? Consult the Midland WR120 user manual for the correct test procedure.

The Bellman editorial team produces content grounded in verified primary sources. Connection steps in this guide come directly from the live Bellman weather emergency alerting page. SAME code information comes from official NWS publications. We do not assert specs without confirmation on current official Bellman product pages.
Sources used in this article:
- NWS - NOAA Weather Radio SAME Code County by County Coverage - weather.gov/nwr/counties
- NWS - Using SAME (Specific Area Message Encoding): programmed using FIPS codes; get code via weather.gov/nwr or 1-888-NWR-SAME (1-888-697-7263) - weather.gov/nwr/usingsame
- NWS - SAME location code format PSSCCC: P is point type (usually 0), SS is state code, CCC is county FIPS code - weather.gov/lix/noaaweatherradios
- NWS - NOAA Weather Radio transmitters typically cover a 40-mile radius on level terrain - weather.gov/nwr/counties
- NWS - NOAA Weather Radio All Hazards operates on seven VHF frequencies: 162.400, 162.425, 162.450, 162.475, 162.500, 162.525, 162.550 MHz - weather.gov/pbz/whatisnwr
This article is for informational purposes only. Bellman alerting products are supplementary devices. They do not replace required building safety systems or emergency services. Always follow official guidance during a weather emergency. Bellman is not affiliated with Midland. Midland products are sold separately. All Midland trademarks belong to Midland.
More in This Series
Complete NOAA Weather Alert Guide for d/HH Americans
The complete guide covering every alert type, full setup, and the preparedness checklist.
🌧What Is the NOAA Storm Prediction Center?
How the SPC monitors severe weather and issues watches for your county.
🌪Tornado Warning vs. Watch for Deaf Households
What each means, when to act, and how to receive both without sound.
🌙Silent Weather Alerts at Night
How the Bed Shaker wakes you during overnight warnings without any sound.
🏘Hurricane Season Preparedness Checklist
A step-by-step guide for Gulf and East Coast households before hurricane season starts.
🔥Wildfire and Red Flag Warning Alerts
What Red Flag Warnings mean for western US d/HH households.
❄Winter Storm and Blizzard Warning Alerts
How to receive NWS blizzard and ice storm warnings through light and vibration.
🔍Best Weather Alert Systems for Deaf Homes (2026)
A buyer's guide comparing daytime, nighttime, and full-home visual alert setups.